Polatlı Chain Link Fence and Fencing Systems

Why Fencing Work in Polatlı Is Always Built Around a Long Run

Polatlı is Ankara's largest farming district and the place where its grain production gathers. What has to be enclosed here is usually not a garden but a field boundary measured in kilometres rather than in metres. That single fact changes every decision: material is worked out by the metre instead of the square metre, post counts climb into three figures, and the number of trips it takes to get everything on site turns into the hidden cost of the job.

Three separate needs overlap in the district. The first is wide field and land boundaries. The second is site security for flour mills, feed plants and agricultural businesses. The third is the perimeters around housing, pens and feed areas on beef and livestock operations. All three call for a different product, a different height and a different post arrangement; applying one answer to all three means either paying too much or ending up with too little protection.

Working Out Running Meters and Post Counts on a Field Boundary

On a long run the first job is to stop guessing. Two formulas will see you through.

Perimeter length: on a rectangular parcel, perimeter = 2 × (long side + short side). On a field of 400 metres × 300 metres that gives 2 × (400 + 300) = 1,400 metres.

Post count: (run length ÷ post spacing) + 1. On the same field at 3 metre spacing, 1,400 ÷ 3 ≈ 467, add 1 and you arrive at 468 posts. That figure includes the corner posts but not the braces: plan a brace at each of the four corners, plus a braced straining post every 30-50 metres.

Wire running meters follow the line itself. With barbed wire, multiply by the number of strands: 5 strands of barbed wire on a 1,400 metre run comes to 7,000 metres of wire. With mesh you divide the total run by the roll length; taking 25 metre rolls as the example, 1,400 ÷ 25 = 56 rolls. Add roughly 5% to both calculations for overlaps and waste. On the post side, concrete posts build a permanent line that needs no maintenance, while steel tube posts are easier to carry and set out.

Site Security for Grain, Flour and Feed Plants

On silo, flour mill, feed plant and agricultural business sites the issue is not animals but vehicle and pedestrian traffic. The choice here generally goes to panel fence: it holds its straight line, on sites with heavy truck movements an impact is repaired by swapping a single panel, and it lines up neatly with camera and lighting columns.

Set the height by what the site holds. If there is open storage and an equipment park, a panel height of 2 metres and above with a deterrent layer on top makes sense; if the fence is only there to mark the boundary, a lower line does the job. Separating the vehicle gate from the pedestrian entrance makes the site easier to control and keeps the main gate from being opened unnecessarily.

One detail that is often missed on plant sites is where the fence line sits in relation to the weighbridge and the loading area. If the ground a truck needs to swing through on its way onto the weighbridge falls inside the fence, that stretch starts taking knocks in the first year. Putting the path of the largest vehicle on site down on paper before the fence route is set out costs far less than replacing panels afterwards.

Choosing Wire and Mesh Aperture Around Feedlots and Housing

What decides an animal fence is the mesh aperture and how tightly the wire is strained. Too large an aperture and the animal puts its head through and works the wire loose; smaller than it needs to be and you are simply paying for nothing. The table below sums up the pairings that prove most useful in practice.

In housing and pen divisions galvanised chain link fence is the common choice; where contact with manure and urine is heavy, the PVC coated option protects the steel under the coating for longer.

Gate Widths for Tractors and Combine Harvesters

The most expensive mistake on a long run is leaving the gate too narrow, because putting it right means opening up a line that has already been strained. Give the dimension as clear opening width, not as the room the leaves need to swing.

• Tractor, plough and trailer access: 4 metres clear
• Baler, feed mixer wagon, tanker: 5 metres clear
• Main entrance used by combines and plant machinery: 6 metres clear and above
• Pedestrian and staff access: a separate gate of around 1 metre

On wide openings a field gate is the most practical answer for field entrances. Allow for the level ground a vehicle needs to turn on in front of the gate as well; a gate can be wide enough and still cause the same trouble if there is no room to manoeuvre. If the same gate will see a lot of movement through the day at harvest, leave a fixing point that holds the leaves open so the wind cannot catch them.

What You Gain by Listing the Whole Requirement in One Go

Because most jobs in Polatlı run to a high number of running meters, haulage deserves as much attention as the material itself. Delivery is always charged, and addresses within Ankara are included in that. Pulling the wire, the posts, the straining and tying materials and the gates onto a single list therefore puts money straight back in your pocket: one drop instead of three separate shipments for the same line brings the transport burden down noticeably.

Do not leave the gates and the braces off the list; those are the items that most often turn out to be missing on site. Even if the parcel is to be fenced in stages, working out the total requirement up front and buying it in one batch removes both the coating and colour variation that comes from different production batches and the second haulage run.

The list to draw up before ordering comes down to six items: wire running meters, intermediate post count, corner and straining post count, number of braces, straining and tying materials, and gates. Write those six out parcel by parcel and gather them into one table, and the quoting stage gets shorter while it is clear from the start how much of the delivered material goes where. In the busy weeks of the harvest calendar, that preparation becomes the detail that decides whether the job is ready in time for the season.

Delivery, Site Surveys and Site Team Terms for Polatlı

Shipments leave our warehouse in Ostim. Polatlı is approximately 80 kilometres away, and once the order is confirmed delivery is planned within 1 business day. The run is short enough that a same-day departure is usually possible; at harvest, the state of the field tracks and whether the vehicle can get into the parcel need discussing beforehand. Delivery is charged in all cases.

Site surveys are free within Ankara, and Polatlı falls inside that. The survey establishes the true length of the line, the ground conditions, the gate positions and the straining points on site. Installation is not a part of our standard service; our teams do, however, attend projects of approximately 1000 metres and above. Because the long field runs in the district mostly sit above that threshold, the rule turns into a practical advantage in Polatlı. All our prices include VAT.